Allis-Chalmers Gleaner F Self Propelled Combine Owners Manual

Description

This 138 page, Allis-Chalmers Gleaner F Self Propelled Combine Owners Manual includes operating instructions for Allis-Chalmers Gleaner F Self Propelled Combines.  This  Allis-Chalmers Gleaner F Self Propelled Combine Owners Manual is a reproduction of the original Allis-Chalmers Gleaner F Self Propelled Combine Owners Manual.

Table of Contents

Function of Combine
GENERAL SERVICE
Batteries
Belt Diagram
Chain & Belts
Chain Elongation
Cleanliness ,
Gear Changes on Transmission
Lubrication
Lubrication of Slip Clutches
Roller Chain Dont’s
Shaft and Sprocket Alignment, V-Belt Care & Adjustment
Wheel Tread
HYDRAULIC SYSTEM SERVICE Control Valve Linkage Adjustment
Filter Replacement
Operating Pressure
Pump Drive Belt Adjustment
LUBRICATION – Combine
LUBRICATION & SERVICE – Engine 292 Gasoline
Air Cleaner, Dry Type
Air Intake Pre-Cleaner
Alternator
Coolant Capacity
Crankcase Oil
Distributor
Dust Cap
Gasoline Requirements
Governor
Oil Filter
Operation Aids
Spark Plugs
Timing (Static & Dynamic) 2800 Diesel
Air Cleaner, Dry Type
Alternator
Belt Adjustment
Crankcase Oil
Coolant Capacity
Engine Fuel Filter
2800 Diesel (Cont’d)
Fuel Priming Pump
Fuel Requirements
Oil Filter
Oil Filter Cap
Operation Aids for Diesel Engines
Pre-Cleaner
OPERATION
Basic Settings for Normal Conditions
Combine Controls
Cylinder Shoe & Adjustments Chart
Field Operation
Operation Aids
Screen Charts
Shield Clamps
Special Crop Information
SAFETY RAM STOP
SAFETY SUGGESTIONS
SETTING UP INSTRUCTIONS
SPECIAL EQUIPMENT
Air Flow Grain Saver
Adjustable Tailer
Cab
Concave Adjustment
Console Tachometer
Dirt Removal Equipment
Draper Pick-Up (Adj Suggestions)
Header Height Control
Header Throwout Clutch
Hydrostatic Transmission
Mud Shields
Perforated and Blank Panels for Cleaning Shoe
and Tailings Elevator
Raddle Clean Out Doors
Scour Kleen
Spreader Board
Straw Chopper
Tachometer
Tailings Elevator Panels
Unloading Tube (Perforated & Blank Covers)
Variable Speed Draper Pick-Up
SPECIFICATIONS
STORING MACHINE
WIRING DIAGRAMS
ADJUSTMENTS
Auger, Header
Bearings, Pre-Lubricated
Brakes
Adjustment
Bleeding Brakes
Hydraulic Turning Brakes
Transmission
Chaffer
Adjustable Chaffer
Axle Shield
Chaffer Location
Chaffer & Sieve Settings
Lip Opening
Tail Gate & Extension
Walker Set-Back Plates
Cleaning Fan
Cleaning Shoe
Concaves
Rasp Bar
Removing Procedure
Rubber Faced Cylinder Bar & Concaves
Safety Door With Access Bottom
Spike Tooth Concaves
Spring Tooth Concavss
Cutter Bar Parts
Guards
Hold Down Clips
Sickle
Sickle Bellcrank
Sickle Travel
Wear Plates
Cylinder
Bar Removal, Inspection, Replacement
Installation
Removal
Cylinder Speed Chart
Leveling
Raising & Lowering
Variable Speed
Door Latch
Drive Belts
Bin Unloading
Countershaft
Harvester
Main
Pivot
Straw Spreader
Traction
Drive Chains
Eccentric
Feeder Beater
Intermediate Reel
Reel
Thresher Beater
Drive Clutch, Separator
Elevator Chains
Feeder Beater
Fingers
Foot Clutch Linkage Adjustment
Idlers
Blocks
Raddle Chains, Adjustment & Removal
Reel
Hume Reel
Hydraulic Reel Lift
Reel Drive Variable Speed
Reel Height
Shield Clamps
Shoe Guide
Slip Clutch
Sprockets
Installation & Operation
Thresher Beater Drive Sprocket
Stop Assembly (Safety)
Throwout Linkage Adjustment
Transmission Clutch & Clutch Pedal
Unloader Tube