Description
The 68 page, John Deere 724 manual is a reproduction of the original, out of print, John Deere 724 Mulch Finisher Operators Manual. This manual provides information related to operating, servicing, and maintaining your John Deere 724 mulch finisher. Whether you’re prepping your fields for spring planting or troubleshooting in the middle of a busy season, this comprehensive operator’s manual is an essential tool for maximizing efficiency and reducing downtime.
This manual walks you through machine setup, operation, and safety procedures, with step-by-step guidance for adjusting depth control, leveling the implement, and managing residue flow. With the John Deere 724 manual, you’ll also get detailed maintenance intervals and lubrication charts to keep the finisher running smoothly across all conditions.
If you are using this Mulch Finisher and encounter challenges with uneven tillage, broken sweeps, or frame wear on the 724 mulch finisher then this manual helps you identify these issues early and provides instructions for proper inspection and repair—helping you extend the life of your equipment.
The John Deere 724 is a popular tool for secondary tillage, and its performance depends heavily on correct setup and routine care. This manual outlines the procedures recommended by John Deere technicians, including proper tongue height alignment, tire inflation guidelines, hydraulic cylinder operation, and folding/unfolding safety.
Whether you’re working with clay-heavy soil or light loam, the manual provides tips for adjusting your mulch finisher to match field conditions. It also covers seasonal storage and pre-season inspection, so you can avoid last-minute repairs when timing is critical.
Don’t rely on guesswork get the information to get the job done right.
Table of Contents
Safety
Transport Safely
Preparing The Tractor
Preparing The Machine
Check Tire Pressure
Level The Mulch Finisher
Lubricate Mulch Finisher
Attaching And Detaching
Attaching Hitch
Checking Depth Control Operation
Checking Wing Fold Operation
Detaching
Transporting
Operating The Machine
Operating Guidelines
Leveling Mulch Finisher
Adjusting Depth Control
Adjusting Depth Control – Single Point
Understanding Hydraulic Depth Control System (Series)
Positioning Disk Scrapers
Adjusting Spring Pressure Of Disk Gangs
Adjusting Disk Gang Height
Adjusting Stabilizer Wheel Down Pressure 19 Ft 4 In. Only
Leveling Wings For 19 Ft. (5.8 M) Model
Leveling Wings For 24 Ft 8 In. & 30 Ft (7.5 & 9.2 M) Models Only
Adjusting Wing Stops
Adjusting Coil Tine Tooth Harrow Height
Adjusting Spike Tooth Drag Harrow Angle
Adjusting Spike Tooth Drag Harrow Height
Adjust Nozzle Height & Spacing For Spray Attachment
Lubrication And Maintenance
Lubrication Symbols
Extreme Pressure Grease
Axle Bearing Grease
Alternative Lubricants
Lubricate Stabilizer Wheel
Troubleshooting
Service
Using Safe Service Procedures
Replacing Ground Engaging Tools
Shovels And Sweeps
Service Tires Safely
Inch Series Torque Chart
Checking Tightness Of Wheel Bolts And Bearings
Checking Torque On Disk Gang Hardware
Tightening Gang Bolts
Setting Torque On Spring-Reset Standards
Increasing Rigidity Of Standards
Installing And Bleeding Wing Fold Cylinders
Bleeding Depth Control Cylinders
Removing Hydraulic Cylinders
Checking For Depth Control Cylinder Leakage
Checking Standard Bushings
Replacing Split-Tension Bushings
Identifying Disk Blades Eligible For Warranty
Identifying Disk Blades Not Eligible For Warranty
Storage
Preparing Machine For Storage
Removing Machine From Storage
Crime Prevention Tips
Good Advice
Record Identification Numbers
Maintain Documented Proof Of Ownership
Park Indoors Out Of Sight
Parking Outdoors
Reduce Vandalism
Report Theft
Specifications
Tractor Recommendations
Machine Dimensions
Tire Size And Inflation
Standards
Disk Gangs
Frame Construction
Standard Or Optional Harrows
Hydraulic Cylinders
Serial Number
